A twelve inch mid bass driver rarely gets the attention a subwoofer gets. That’s a shame, because it carries the part of a live mix people notice first, and it’s the part you can’t put right at the desk. Vocals sit in this band. So does most of a guitar’s body, and the lower half of a snare. We build and supply these from Zhejiang, and much of what reaches our desk comes from cabinet makers who already have a box and need something that drops into it without a redesign. That’s a different conversation from picking a woofer off a catalogue, and it’s worth explaining where the two part company.

Where a mid bass sits between the woofer and the horn
In a three way cabinet the split looks tidy on paper. The woofer takes the bottom, the horn takes everything above roughly 1.5 kHz, and the mid bass fills what’s left. In practice that leftover band is where crossovers do the most harm, because it’s where the ear is most fussy and where two drivers are still making sound at the same time. A driver that measures flat on its own can vanish once you hang a filter in front of it. So we ask which crossover points you’re designing to before we recommend anything, not afterwards.
There’s a second reason the band matters. Voice fundamentals live here, and so does the range where a room’s early reflections pile up. If the driver sits a couple of dB down across that band, the rig sounds distant even when a meter at front of house says the level is fine. Nobody blames the driver for that. They blame the room, or the desk, and then they buy a bigger amplifier.

Paper cone, and why people argue about surrounds
The twelve inch mid bass speaker driver we build most often, the H-12BHP300, uses a paper cone. People ask about that a lot. Paper hasn’t lasted sixty years because it’s cheap, though it is. It lasts because it’s light, it’s well damped, and it breaks up gradually instead of ringing at one frequency. A stiffer material can look flatter on a swept sine and still sound harder in a room, because its breakup modes land in a narrow band where the ear is least forgiving.
The surround is the other half of that decision. It sets how far the cone can travel before it runs out of travel, and it decides how the driver behaves at the bottom of its range. In a ported box tuned low, the surround is doing more work than the cone is. We don’t print one excursion figure for it, because that number doesn’t mean much until you put it next to your port tuning. Send the volume and the tuning and we’ll send back the curve rather than a single figure.
The basket carries the load
A die-cast aluminium basket isn’t a styling choice. Twelve inch ferrite motors are heavy, and the basket holds that weight off the cone and off the voice coil gap. If it flexes, the gap shifts under load and you hear it as a roughness that comes and goes with level. Cast baskets also pull heat out of the motor, which matters more in this band than people expect, because the material it carries is dense and the coil spends most of a set warm.
Our die-cast aluminium basket version and the professional audio mid bass speaker share that approach. If you’re building a lighter box for install work, ask us about the pressed steel alternative and we’ll tell you honestly where the trade-off lands, including the places where pressed steel is genuinely the better answer.

Inside wound, outside wound
The H-12BHP300 carries a three inch voice coil wound in and out, which is a detail most spec sheets skip. An inside/outside wind puts copper on both faces of the former. That moves heat into the motor faster and it lets the coil stay short enough to keep moving mass down. What you get is a driver that holds its sensitivity after twenty minutes at level instead of sagging. If your boxes are going into a room that runs long sets, that’s the line on the sheet worth reading twice.
It isn’t free. The winding takes longer to make and it costs more per unit. For a background music system that’ll never see high level, you don’t need it, and we’ll say so rather than sell it to you.
A sensitivity figure is only half a sentence
Our twelve inch reads 97.5 dB. That’s measured at one watt at one metre, and it’s the number buyers sort by, which is unfortunate. Sensitivity tells you how loud a driver goes on a given input, but it says nothing about how it behaves across the band you’re actually asking it to cover. Two drivers with identical sensitivity can land in very different places once the crossover has taken its share out.
What we’d rather you look at is the response between your own crossover points, and how much power the driver needs to reach the level your box is meant to hit. Tell us the target SPL and the filter and we’ll tell you whether 97.5 dB is enough, or whether you need a fifteen inch neo woofer sitting underneath it to carry the bottom.

Three checks before a driver programme
- Ask for the impedance curve, not just the nominal value. An eight ohm driver that dips lower at a frequency you push hard will make your amplifier unhappy, and you’ll find that out on a gig rather than on a bench.
- Ask what happens to the cone supply in year two. Paper comes from a mill, mills change furnish, and a supplier who can’t explain how they hold the batch steady will hand you a different driver next spring and call it the same part.
- Ask who winds the coil and whether they audit that workshop. If the answer is vague, your replacement order won’t match the pair you already measured.
None of those three need a factory visit. They need a supplier who’ll answer in writing, which is a lower bar than it sounds and still filters out more than half the field.
Matching a driver to a box that already exists
Replacement work is its own discipline. You have a cut-out diameter, a mounting depth, a port tuning and a crossover that was designed around a part you can no longer buy. Change one of those and you usually have to change another. In practice the constraint that bites first is depth, because a deeper motor won’t clear the back panel and a shallower one won’t give you the excursion you had.
Send us the internal dimensions, the port, and a photo of the original driver’s label if you still have it. We’ll tell you whether something on our shelf drops in, or whether it needs a tool. If it needs a tool we’ll tell you what that costs up front, because a small tooling charge on a repeat programme is usually cheaper than a year of living with a driver that doesn’t quite fit.

Mixed containers, and what travels well beside a driver
Drivers pack badly if you let them. A twelve inch ferrite motor is dense, and a pallet of them reaches the weight limit long before it reaches the volume limit, so the freight line is set by mass rather than by space. That argues for filling the leftover volume with something light. Our repeat buyers put Yinyu stands in the same container for exactly that reason, and Yinyu cables coil into cartons that take whatever shape is left.
The other thing worth planning is the foam. Cones don’t ship well with dust caps taking the load, and a carton that stacks three high will crush the bottom one somewhere around the second leg of the voyage. We pack to a five ply carton with a ring that carries the load on the basket rather than on the cone. Yinyu stands travel in the same carton standard, so the pallet stacks evenly.
What we do when your box arrives
We don’t drop a driver in and play music at it. We run it in your enclosure, measure at the crossover points you gave us, and listen at the level you say the box is meant to reach. Then we send the curves back. If something doesn’t work we’d rather say so at sample stage than ship four hundred units and argue about it afterwards.
Ningbo Lesound Electronics is set up for OEM and ODM work on this kind of part, and sample based development is what we do most of. Audfine headphones and Yinyu stands come out of the same inspection routine, so a dealer who runs a full catalogue isn’t dealing with three separate quality regimes.

Questions we get before a mid bass order
What do you need from us before a mid bass driver can be quoted?
The box volume, the port tuning, the crossover points you’re designing to and the target SPL. Without those four we can quote a part number, but we can’t tell you whether it’ll work in your cabinet. If you only have an existing driver, send us its label and the internal dimensions instead and we’ll work backwards from there.
Can you match a driver that’s already in our box?
Often, yes, though it depends on which dimension is tight. Mounting depth is usually the one that stops us, because a deeper motor won’t clear the back panel. Send a photo of the original driver’s label plus the internal dimensions and we’ll tell you what drops in and what needs a tool.
Is ferrite still the right magnet for a twelve inch mid bass?
For most fixed installations, yes. Ferrite costs less and it doesn’t care about heat the way some neo grades do. Neo wins where the box has to be carried up a flight of stairs or flown, and that’s a decision about your product, not about which magnet sounds better.
How do you hold cone batches steady between orders?
We buy cone paper to a written furnish and keep a retained sample from every production run. If you reorder eight months later and the curve has moved, we can show you both samples side by side. Ask any supplier for that retained sample and see how long the pause is before they answer.
Can a mid bass driver share a container with stands and cables?
That’s how most of our repeat shipments go. Drivers are dense and hit weight limits early, so the empty volume is better filled with something light. Yinyu stands pack flat, Yinyu cables coil into cartons, and Audfine headphones take the remaining corners. One container, one set of documents.
What happens if the sample doesn’t measure the way we expected?
We say so. We run the driver in your enclosure, measure at your crossover points and send the curves back before anything moves to production. If it doesn’t work we’d rather lose the sample cost than ship a container you’ll be unhappy with for a year.
If you’ve got a cabinet and a crossover and you’re not sure what belongs in the middle of it, send us the drawing. Put the word midbass in the subject line so it reaches the right bench. Otherwise, start from the contact page on our site and we’ll take it from there.
Post time: Oct-16-2026



