A spec sheet for a horn tweeter is short, and that’s exactly why buyers get caught out. Four lines, half a dozen numbers, and none of them tell you whether the part will survive in your box. We build and export these from Zhejiang, and the enquiries that go wrong almost always go wrong because someone read the sensitivity figure and stopped there.

The throat size is a joint, not a hole
One inch is the common throat, and it’s the first number on every sheet. What it actually describes is the exit the driver couples into. If the horn’s entrance doesn’t meet that exit cleanly, you get a reflection at the joint that shows up as a ripple in the top octave, and no amount of EQ removes a reflection. It’s a mechanical fit before it’s an acoustic one.
So the question isn’t only what throat the driver has. It’s what throat your horn was cut for, and whether the two were made to the same tolerance. Send us the horn part number if you have it and we’ll check the pair rather than the driver alone.
Phenolic, and where it wins against titanium
Our NHP4000 runs a phenolic diaphragm. Phenolic is fabric set in resin, it damps well, and it doesn’t ring the way a thin metal dome can. The trade is simple: it gives up sooner at sustained high level. Titanium holds up longer and costs more, and it’s the right call for a box that will be driven hard for six hours a night.
Where phenolic wins is every installation that isn’t. Ceiling speakers, compact boxes in a bar, anything crossed above about 1.5 kHz and run at sane level. Our one inch titanium tweeter covers the other end of that range, and we’ll happily tell you which one we’d put in your box if you describe the room.

Bolt-on or screw-on, and the tooling that follows
The NHP4000 is bolt-on. That’s a flange with four holes, and it’s more rigid once it’s fitted, which is why install boxes tend to use it. The cost is that your horn has to be made for it. Screw-on parts thread into a standard one inch horn and can be swapped without touching tooling, which is why rental stock leans that way.
If you’re specifying a new product, choose on how you’ll assemble it in year three, not on which is technically nicer. Our bolt-on compression driver is the bolt-on we build in volume, and we’ve watched buyers switch from one to the other purely because a line changed.
One hundred and seven decibels, at what frequency
Sensitivity on a horn driver is quoted as a single figure and it isn’t one. Output varies across the band, and the number on the sheet is usually an average or a value at one frequency. Two drivers can both claim 107 dB and behave completely differently between 2 kHz and 8 kHz, which is the region where listeners decide whether a top end is smooth or sharp.
Ask for the curve. Any supplier who’ll only give you the average is telling you something, and it isn’t that they’re busy.

The horn itself is half the design
On our NHP4000 the horn is moulded plastic and it comes as part of the assembly. That matters more than people think, because the flare sets the dispersion pattern. A driver measured on a plane wave tube tells you what the motor does. It tells you nothing about how wide the pattern is at 4 kHz, which is what the room actually receives.
If you’ve tooled your own waveguide, we can supply the driver without the horn. Say so on the enquiry, because the bare part needs different packing and it changes what we quote.
Seven checks before a horn tweeter order
- Throat diameter, and whether your horn entrance was cut to the same tolerance.
- Diaphragm material, chosen against the crossover point rather than against the price.
- Bolt-on or screw-on, decided by how you’ll assemble in year three.
- The response curve, not the averaged sensitivity value.
- Whether the horn ships with the driver or separately.
- Magnet grade and working temperature, if the box will sit in a hot ceiling void.
- How failures get traced back to a production run.
Seven lines. Most of them take one email to answer, and the answers tell you more than a factory tour would.

What fails in the field, and what doesn’t
Diaphragms fail. Voice coils rarely burn on their own. When we get a warranty claim back it’s nearly always a crossover set too low, or an amplifier driven into clipping that sends high frequency energy into a driver that was never meant to see it. That’s a system problem wearing a driver’s face.
If you’re seeing repeat failures in one installation, tell us the crossover frequency and the amplifier size before you order replacements. Changing the driver won’t fix a filter that’s asking too much of it.
Packing a small part with a plastic horn
The horn protects the diaphragm in transit, which is why we’d rather ship them assembled. A bare driver needs an insert that keeps load off the dome, and that insert costs more than the saving from dropping the horn. Small parts also disappear easily in a warehouse, so we pack to a fixed carton count rather than a weight.
Most of our horn tweeter orders don’t travel alone. Dealers add Yinyu stands to the same purchase order, Yinyu cables fill the carton space, and Audfine headphones round out the catalogue. One shipment, one inspection, one set of documents.
Ceiling work, and the void above the tile
A horn driver in a ceiling box lives somewhere nobody looks. The void above a tile gets hot in summer, and heat is what finishes a diaphragm early. If your product is going into that space, tell us, because the magnet grade and the adhesive we pick change with the working temperature.
The other thing about ceiling work is access. Nobody wants to pull a driver out of a ceiling twice, so the mounting has to be right the first time. Bolt-on earns its keep here, and it’s the reason our NHP4000 ships that way rather than with a thread.
Spare parts and the service van
The diaphragm is replaceable. A venue engineer with a spare on the shelf can fix a failed driver between soundcheck and doors, and one without waits three weeks. If you sell into rental or installation stock, order diaphragms alongside the drivers and label them as service parts rather than as stock.
Contractors who carry Yinyu stands and Yinyu cables on the same van often add these at the same time, because the service call that finds a dead driver usually finds something else worth fixing while the ladder is up.
How an OEM enquiry usually starts
It starts with a curve and a throat size, not with a part number. You tell us the response you need, the mounting your horn takes and the environment the box will sit in, and we tell you what we can hit from tooling we already hold. Where it needs a new part made, we say so at the start rather than after the schedule is agreed.
From there it’s a sweep per unit, a log against the batch and a retained sample per run. We’ve run that routine at Ningbo Lesound Electronics on every driver programme taken on, and dealers who put Audfine headphones and Yinyu stands on the same programme go through the identical bench, so adding a line doesn’t add a quality regime.
Questions we get before a horn tweeter order
What does bolt-on mean here, and does it matter for a replacement?
It means the driver carries a flange with bolt holes instead of a screw thread. For a replacement it matters a great deal, because a bolt-on part won’t drop into a horn that was cut for a thread. Check which one your horn was made for before ordering, or send us a photo and we’ll tell you.
Why is the phenolic diaphragm rated lower than titanium?
Phenolic is a resin-impregnated fabric and it gives up before titanium does at sustained high level. What you get back is a smoother top end at modest level, with none of the edge a thin metal diaphragm can produce when it’s crossed over too low. For most ceiling and compact box work that’s the trade worth making.
Does the horn come with the driver?
On our NHP4000 yes, the plastic horn is part of the assembly. Some buyers want the driver alone because they’ve tooled their own waveguide. Tell us which you need when you enquire, because the packing and the price differ.
How do you keep sensitivity consistent from batch to batch?
We measure every unit, log it against the production run, and keep a retained sample from each run. If a reorder moves outside the tolerance we agreed, we’d rather flag it before shipping than let you find it on the line.
Can we order the driver without the horn attached?
Yes. It changes the packing, because the horn is what protects the diaphragm in transit, so a bare driver needs a different insert. Say so on the enquiry and we’ll quote the packed version rather than assuming.
What fails first on a horn tweeter in the field?
Usually the diaphragm, and usually because the crossover point was set too low or the system was driven into clipping. The voice coil doesn’t often burn on its own. If you’re seeing repeated failures in one installation, send us the crossover frequency and we’ll tell you whether the driver is being asked to do a job it wasn’t built for.
If you’ve got a horn and you’re not sure which driver belongs on the back of it, send us a photo and the crossover frequency. Otherwise start from the contact page on our site and we’ll take it from there.
Post time: Oct-19-2026



